安裝流程

Installation process

1. 基礎施工

1. Foundation construction

根據大門的尺寸和重量，在門洞兩側澆筑混凝土基礎。基礎深度一般為 60 - 80 厘米，寬度比大門邊框寬 10 - 20 厘米。在澆筑過程中，將預埋件（通常為鋼板或角鐵）按照設計要求固定在基礎中，預埋件的位置和水平度必須精確，誤差不超過 5 毫米，為后續大門的安裝提供穩定支撐。

According to the size and weight of the gate, pour concrete foundations on both sides of the doorway. The basic depth is generally 60-80 centimeters, and the width is 10-20 centimeters wider than the door frame. During the pouring process, the embedded parts (usually steel plates or angle irons) are fixed in the foundation according to the design requirements. The position and levelness of the embedded parts must be precise, with an error of no more than 5 millimeters, providing stable support for the subsequent installation of the gate.

2. 大門安裝

2. Gate installation

待基礎混凝土達到一定強度（一般需養護 7 - 10 天）后，開始安裝鐵藝大門。將大門抬至門洞處，通過調整墊片，使大門保持垂直和平整，利用水平儀進行檢測，確保垂直度誤差不超過 3 毫米。然后，使用電焊機將大門邊框與預埋件牢固焊接，焊接點應均勻、飽滿，焊縫高度不低于 5 毫米。焊接完成后，對焊接部位進行打磨處理，使其表面光滑平整。

After the foundation concrete reaches a certain strength (usually requiring 7-10 days of curing), the installation of the wrought iron gate can begin. Lift the gate to the doorway and adjust the gasket to keep it vertical and flat. Use a level to check and ensure that the verticality error does not exceed 3 millimeters. Then, use an electric welding machine to firmly weld the door frame to the embedded parts. The welding points should be uniform and full, and the weld height should not be less than 5 millimeters. After welding, polish the welding area to make its surface smooth and flat.

3. 配件安裝

3. Accessory installation

安裝合頁時，要確保合頁的軸心線垂直，合頁間距一般為 30 - 50 厘米。使用配套的螺絲將合頁固定在大門邊框和墻體上，螺絲要擰緊，防止松動。安裝門鎖時，選擇質量可靠的產品，根據門鎖的類型和安裝要求進行操作，確保門鎖開關靈活，鎖芯安全可靠。此外，還需安裝門吸或地鎖，防止大門在開啟或關閉時晃動。

When installing hinges, ensure that the axis of the hinges is perpendicular, and the hinge spacing is generally 30-50 centimeters. Use matching screws to secure the hinges to the door frame and wall, and tighten the screws to prevent loosening. When installing a door lock, choose a reliable product and operate it according to the type and installation requirements of the door lock to ensure that the door lock switch is flexible and the lock cylinder is safe and reliable. In addition, it is necessary to install a door stopper or floor lock to prevent the door from shaking when opened or closed.

調試與驗收

Debugging and acceptance

1. 調試

1. Debugging

安裝完成后，對鐵藝大門進行全面調試。反復開關大門，檢查其運行是否順暢，有無卡頓、異響等現象。調整合頁和門鎖的位置，確保大門關閉后緊密貼合，無縫隙。同時，檢查門吸和地鎖的工作狀態，保證大門在固定位置穩定可靠。

After installation, conduct comprehensive debugging of the wrought iron gate. Repeatedly open and close the door, check whether it runs smoothly, and whether there are any lagging, abnormal noises, or other phenomena. Adjust the position of hinges and door locks to ensure a tight fit without gaps after the door is closed. At the same time, check the working status of the door latch and floor lock to ensure that the door is stable and reliable in its fixed position.

2. 驗收

2. Acceptance

邀請業主對安裝工程進行驗收。驗收內容包括大門的外觀、安裝質量、使用性能等方面。檢查大門表面是否有劃痕、掉漆等缺陷，焊接部位是否牢固，配件是否齊全。此外，測試大門的防盜性能，確保其能有效保障場所安全。若發現問題，及時進行整改，直至業主滿意。

Invite the owner to inspect and accept the installation project. The acceptance content includes the appearance, installation quality, and performance of the gate. Check whether there are scratches, paint peeling and other defects on the surface of the gate, whether the welding parts are firm, and whether the accessories are complete. In addition, test the anti-theft performance of the gate to ensure that it can effectively guarantee the safety of the venue. If any problems are found, they should be rectified in a timely manner until the owner is satisfied.

本文由濟南鐵藝大門友情奉獻.更多有關的知識請點擊:http://www.coagfreight.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from Jinan Iron Art Gate For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message